描述
物理参数
颜色： Grey, iron red, blue (specialized seawater corrosion-resistant colors, customizable upon request to facilitate underwater inspection and identification)
光泽： Matt / Flat (for underwater sections), Semi-gloss (for coastal exposed sections)
标准膜厚度：
湿薄膜厚度(WFT): 190 μm
干膜厚度(DFT): 75 μm
理论上传播率： Approx. 4.7 ㎡/kg
闪点： 43°C
密度： Approx. 1.38 g/cm³ (after mixing the two components)
应用程序的说明
混合比例： Base : Curing Agent = 10 : 1 (by weight)
Pot Life (23°C): 2小时
稀释剂: Seawater-Resistant Coating Dedicated Thinner (Note: The use of general thinners is strictly prohibited as it will degrade the film’s seawater resistance and adhesion.)
清洁剂： Seawater-Resistant Coating Dedicated Thinner. Clean all tools immediately after use to completely remove residual paint, preventing cleanup difficulties and tool blockages caused by product curing.
应用的方法： 无空气喷洒，常规的空气喷洒，或者刷/罗涂层。
喷参数
| 参数 | 无气喷雾 | 常规的空中喷雾 | 刷/滚 |
| 喷嘴/尖端的尺寸 | (Graco) 163T-621/623 | 2.8 ~ 3.0 mm | — |
| 流体压力(MPa) | 19 ~ 42 | 0.45 ~ 0.65 | — |
| 疏比 | 0 ~ 5% | 5 ~ 12% | 5 ~ 12% |
Note: Airless and conventional air spray data are for reference only and can be adjusted based on onsite conditions during practical application.
Drying Time & Full Curing Time
| 基Temp. (°C) | Surface Dry (min) | 硬干(h) | Full Curing Time (h) |
| -5 | 190 | 26 | 72 |
| 10 | 95 | 13 | 48 |
| 20 | 60 | 8 | 24 |
| 30 | 32 | 6 | 16 |
表面准备
The surface of the substrate or intermediate coat must be clean, dry, and completely free of oil stains, corrosion, old paint residue, marine growth, and salts.
Surface cleanliness should reach Sa2。5 grade (abrasive blasting) or Ah3 grade (manual/power-tool cleaning). Remove surface salts, dirt, and dust thoroughly using high-pressure fresh water to prevent residual salts from compromising corrosion resistance. Allow the surface to dry completely (moisture content $\le$ 6%) before application.
When overcoating existing seawater corrosion-resistant paint or epoxy coatings, the old film must be abraded and roughened to eliminate chalked, loose, or peeling areas, ensuring excellent intercoat adhesion and preventing delamination.
应用程序的条件
温度及湿度： The application temperature range is -5 ~ 35°C with a relative humidity (RH) below 85%. The substrate surface temperature must be at least 3°C above the dew point. All measurements of temperature and humidity must be taken close to the substrate in the application area.
Underwater Operations: For specialized underwater application contexts, the seawater flow velocity must be controlled at $\le$ 1 m/s to ensure normal film formation.
High-Temperature Constraints: Coating operations are not recommended if the substrate surface temperature exceeds 48°C, avoiding film defects like pinholes, wrinkling, or incomplete curing.
Adverse Weather: Outdoor application is strictly prohibited during rain, snow, heavy winds, sandstorms, dense fog, high humidity, or immediately before a rainstorm. For underwater applications, avoid periods of high waves and strong swells to ensure construction safety and coating quality.
Sub-Zero Operations: For applications below 0°C, the substrate surface must be entirely free of ice, snow, or frost, and anti-freezing measures must be taken to guarantee normal film formation.
涂层系统的兼容性
Preceding Coats: SH-E1501 Zinc-Rich Epoxy Primer or SH-E1502 Epoxy MIO Intermediate Paint.
System Recommendation: For the full immersion zone, pairing with a specialized seawater corrosion-resistant intermediate paint is recommended to enhance protection. For coastal exposed sections, this product can be directly matched as the topcoat. Using these in combination creates a complete, long-term seawater corrosion-resistant system.
包装的规格
基地(A部分): 20公斤
固化剂(B部分): 2 kg
储存
Store this product in a cool, dry, and well-ventilated indoor warehouse, away from open flames and heat sources. Avoid direct sunlight.
Do not store together with acidic or alkaline substances. The shelf life is 12个月 under normal room temperature (5-30°C) conditions.
The base and curing agent must be stored separately. Once opened, the product should be used as soon as possible; any unused portion must be tightly sealed and stored.
安全预防措施
All sources of ignition and smoking are strictly prohibited at the mixing and application sites. Maintain excellent ventilation to reduce paint mist concentration and avoid the inhalation of harmful components (especially in confined spaces or high-altitude environments where ventilation protection must be reinforced).
Applicators must wear appropriate personal protective equipment (PPE), including protective masks, safety goggles, solvent-resistant gloves, and anti-slip shoes. Safety harnesses are mandatory for high-altitude operations to prevent falls, paint mist inhalation, or eye and skin contact.
If paint contacts the skin, wash immediately with soap and water or a specialized skin cleanser. If it splashes into the eyes, rinse continuously with plenty of water for at least 15 minutes and seek immediate medical attention.
Warning signs must be placed around the application area to restrict unauthorized entry. Clean up and collect residual coatings and thinners promptly after construction for centralized disposal to avoid polluting the marine and surrounding environments.
免责声明
保护性能的任何涂层在很大程度上取决于应用程序因素。 表面准备和薄膜厚度将会直接影响到服务的生活的涂层。 用户必须确保遵守规定的应用条件。
提供的数据，在这本手册是理论上的价值或来源于实验的积累。 一些数据可以改变由于持续的产品的改进，无须事先通知。
当我们的公司的技术人员都是不存在的应用程序的网站，该公司承担全部责任的质量的涂料产品本身。
