描述
物理参数
颜色： Greyish black, silver grey
光泽： Matt/平
标准膜厚度：
湿薄膜厚度(WFT): 65 μm
干膜厚度(DFT): 20μm
理论上传播率： Approx. 12.5 ㎡/kg
闪点： 32°C
密度： Approx. 1.38 g/cm³ (after mixing the two components)
应用程序的说明
混合比例： Base : Curing Agent = 2 : 1 (by weight)
Pot Life (23°C): 2小时
稀释剂: Inorganic Zinc Dedicated Thinner
清洁剂： Tap water (Note: For organic solvent-borne coatings, usually a solvent or specialized thinner is required for a complete system flush if the product hardens. Ensure lines are flushed thoroughly while the product is still fluid.)
应用的方法： 无空气喷洒，常规的空气喷洒，或者刷/罗涂层。
喷参数
| 参数 | 无气喷雾 | 常规的空中喷雾 | 刷/滚 |
| 喷嘴/尖端的尺寸 | (Graco) 163T-621/623 | 1.5 ~ 2.0 mm | — |
| 流体压力(MPa) | 15 ~ 35 | 0.35 ~ 0.55 | — |
| 疏比 | 0 ~ 5% | 5 ~ 15% | 5 ~ 15% |
Note: Airless and conventional air spray data are for reference only and can be adjusted based on onsite conditions during practical application.
干燥的时间和间隔复涂
| 基Temp. (°C) | Surface Dry (min) | 硬干(h) | 分。 复涂间间隔(h) | 最大。 复涂间间隔 |
| 5 | 40 | 12 | 6 | 没有限制 |
| 15 | 25 | 6 | 4 | 没有限制 |
| 20 | 15 | 4 | 2 | 没有限制 |
| 30 | 8 | 2 | 1 | 没有限制 |
表面准备
The steel surface must be clean, dry, and completely free of oil stains, impurities, and salts.
Surface cleanliness must reach Sa2。5 grade via abrasive blasting, with the surface profile (roughness) controlled within 35 to 65 μm.
To prevent secondary flash rusting, this shop primer must be applied within 4 hours of blasting completion.
Existing old paint films must be completely removed by grinding or blasting; this product is not suitable for overcoating or touch-up maintenance over old paint.
应用程序的条件
温度及湿度： The application temperature range is 5 ~ 40°C with a relative humidity (RH) below 85%. The substrate surface temperature must be at least 3°C above the dew point.
制约因素： Humidity levels must be monitored carefully; excessively high humidity may induce whitening or chalking of the film. Outdoor application is strictly prohibited during rain, snow, dense fog, or severe wind and sandstorms.
Production Line Safety: Maintain a clean, ventilated, and dry application environment. Avoid dust accumulation or falling debris on the production line while the coating dries.
涂层系统的兼容性
Subsequent Coats (Intermediate/Topcoats): Epoxy MIO (Micaceous Iron Oxide) Intermediate Paint, Epoxy Anti-Rust Paint, Polyurethane Topcoat, Acrylic Topcoat, or specialized Marine Anti-Corrosive Coatings.
包装的规格
基地(A部分): 20公斤
固化剂(B部分): 10 kg
储存
Store this product in a cool, dry, and well-ventilated indoor warehouse, away from open flames, sparks, and heat sources. Protect from direct sunlight and rain.
The storage temperature range must be maintained between 5°C and 30°C. The shelf life is 12个月 under normal conditions.
The base and curing agent must be stored separately.
安全预防措施
This product contains organic solvents and is a flammable coating. Open flames, welding sparks, and smoking are strictly prohibited at the application and mixing sites. Maintain forced ventilation at all times.
Applicators must wear appropriate personal protective equipment (PPE), including organic vapor respirators, safety goggles, and solvent-resistant gloves. Avoid inhalation of paint mist.
If the coating contacts the skin, clean it first with a specialized thinner or cleanser, and then wash thoroughly with soap and water. If it splashes accidentally into the eyes, rinse continuously with a large volume of water and seek immediate medical attention.
免责声明
保护性能的任何涂层在很大程度上取决于应用程序因素。 表面准备和薄膜厚度将会直接影响到服务的生活的涂层。 用户必须确保遵守规定的应用条件。
提供的数据，在这本手册是理论上的价值或来源于实验的积累。 一些数据可以改变由于持续的产品的改进，无须事先通知。
当我们的公司的技术人员都是不存在的应用程序的网站，该公司承担全部责任的质量的涂料产品本身。
