描述
物理参数
颜色： 各种颜色
光泽： High gloss, Semi-gloss
标准膜厚度：
湿薄膜厚度(WFT): 95 μm
干膜厚度(DFT): 40μm
理论上传播率： Approx. 7.5 ㎡/kg
闪点： Non-flammable
密度： Approx. 1.3 g/cm³
应用程序的说明
混合比例： Two-component (mix Part A and Part B thoroughly in their specified proportions prior to use)
稀释剂: Deionized water
清洁剂： Tap water
应用的方法： 无空气喷洒，常规的空气喷洒，或者刷/罗涂层。
喷参数
| 参数 | 无气喷雾 | 常规的空中喷雾 | 刷/滚 |
| 喷嘴/尖端的尺寸 | (安全)163T-619/621 | 1.8 ~ 2.5 mm | — |
| 流体压力(MPa) | 15 ~ 35 | 0.3 ~ 0.4 | — |
| 疏比 | 0 ~ 5% | 0 ~ 15% | 0 ~ 5% |
Note: Airless and conventional air spray data are for reference only and can be adjusted based on onsite conditions during practical application.
干燥的时间和间隔复涂
| 基Temp. (°C) | Surface Dry (min) | 硬干(h) | 分。 复涂间间隔(h) | 最大。 复涂间间隔 |
| 5 | 100 | 24 | 12 | 没有限制 |
| 15 | 50 | 12 | 8 | 没有限制 |
| 20 | 30 | 8 | 6 | 没有限制 |
| 30 | 15 | 5 | 3 | 没有限制 |
表面准备
Prior to application, ensure that the preceding primer or intermediate coat is completely dry, clean, and free of oil stains, dust, salts, and other impurities. The underlying paint film must be smooth, firm, and free of loose flaking.
When overcoating existing coatings, the old paint layer must be thoroughly abraded and roughened to eliminate chalked or aged areas. Clean off all dust before application to guarantee robust intercoat adhesion.
应用程序的条件
温度及湿度： The application temperature range is 5 ~ 35°C with a relative humidity (RH) below 80%. The substrate surface temperature must be at least 3°C above the dew point.
制约因素： Application is strictly prohibited in condensing environments, heavy fog, or high humidity to prevent film defects like whitening or loss of gloss. Do not apply outdoors during rain, snow, or severe wind and sandstorms.
Sub-Zero Warning: Construction and storage ambient temperatures must never fall below 0°C. Freezing temperatures will break the emulsion phase and ruin the coating.
涂层系统的兼容性
Preceding Coats: Waterborne Zinc-Rich Primer, Waterborne Epoxy Primer, Epoxy MIO (Micaceous Iron Oxide) Intermediate Paint, or Waterborne Acrylic Primer.
System Constraint: Do not pair directly with aggressive, strong solvent-borne coatings to prevent lifting or wrinkling (“paint biting”) of the undercoat.
包装的规格
24 kg / set (Base Paint Part A: 21 kg + Curing Agent Part B: 3 kg)
储存
Store this product in a cool, dry, and well-ventilated indoor warehouse, away from heat sources. Ensure protection against freezing and direct sunlight.
The base paint and curing agent must be stored separately. Maintain the storage temperature range between 5°C and 30°C. The shelf life is 12个月 under standard room temperature conditions.
安全预防措施
This product is a waterborne coating and is non-flammable and non-explosive. Maintain excellent ventilation throughout the application site.
Applicators must wear appropriate personal protective equipment (PPE), including dust/mist masks, safety goggles, and solvent-resistant gloves. Avoid inhaling paint mist.
If paint contacts the skin, wash thoroughly with soap and water. If it splashes accidentally into the eyes, rinse immediately with a large volume of water and seek immediate medical attention. Clean all tools with tap water immediately after use.
免责声明
保护性能的任何涂层在很大程度上取决于应用程序因素。 表面准备和薄膜厚度将会直接影响到服务的生活的涂层。 用户必须确保遵守规定的应用条件。
提供的数据，在这本手册是理论上的价值或来源于实验的积累。 一些数据可以改变由于持续的产品的改进，无须事先通知。
当我们的公司的技术人员都是不存在的应用程序的网站，该公司承担全部责任的质量的涂料产品本身。
