描述
物理参数
颜色： Brown, Silver brown, Grey
光泽： Matt/平
标准膜厚度： * Wet Film Thickness (WFT): $200\,\mu\text{m}$
干膜厚度(DFT): $100\,\mu\text{m}$
理论上传播率： 约。 $4.2\,\text{m}^2/\text{kg}$
闪点： $28^\circ\text{C}$
密度： 约。 $1.55\,\text{g/cm}^3$ (after mixing the two components)
应用程序的说明
混合比例： Base : Curing Agent = 7 : 1 (by weight)
Induction Time: 15 min
锅生(23美元^\circ\文字{C}$): 4 hours
稀释剂: Epoxy Thinner
Application Method: Airless Spray / Conventional (Air) Spray / Brush or Roller
| 参数 | 无气喷雾 | Conventional Spray | 刷/滚 |
| Nozzle/Orifice | (Graco) 163T-621/623 | 2.5~3.0 mm | – |
| 流体压力(MPa) | 15~35 | 0.4~0.6 | – |
| Thinned Volume | 0~5% | 5~15% | 5~15% |
Tool Cleaning: Epoxy Thinner
Note: The parameters for airless spray and conventional spray are for reference only and can be adjusted during practical application.
干燥的时间和间隔复涂
| 基Temp. (∘C) | Surface Dry (min) | 硬干(h) | Min. Overcoating (h) | 最大。 复涂间间隔 |
| 5 | 180 | 36 | 24 | Extended / No maximum limit |
| 15 | 100 | 24 | 12 | Extended / No maximum limit |
| 20 | 60 | 16 | 8 | Extended / No maximum limit |
| 30 | 35 | 10 | 6 | Extended / No maximum limit |
表面准备
For steel structures, the substrate must be blast-cleaned to Sa2.5 standard to remove mill scale, grease, salt, and rust. For concrete substrates, the surface must be sound, dry, free of hollows/voids, and free of loose dust, with a moisture content of $\le 8\%$, and ground smooth. Loose or weak substrates require consolidation treatment. Existing/old paint films must be thoroughly abraded/roughened and cleaned prior to application.
应用程序的条件
The application temperature range is 5–$35^\circ\text{C}$, with relative humidity (RH) below 80%. The substrate surface temperature must be at least 3美元^\circ\文字{C}$ above the dew point. Application under damp, condensing, or rainy conditions is strictly prohibited to prevent the paint film from blistering or whitening. Do not perform outdoor application during high winds, sandstorms, or heavy fog. Maintain good ventilation during application to prevent dust from settling on the uncured film surface.
Coating System
前面的外套: Epoxy zinc-rich primer, or epoxy anti-corrosive primer.
随后的外套: Epoxy topcoat, or polyurethane topcoat.
Note: Avoid compatibility with alkyd-based coatings to prevent adverse chemical reactions.
包装的规格
基地(A部分): 21 kg / 28 kg
固化剂(B部分): 3 kg / 4 kg
储存
This product must be stored in a cool, dry, and well-ventilated indoor warehouse, away from fire and heat sources, and protected from direct sunlight and rain. The storage temperature should be between 5–$30^\circ\text{C}$. Base and curing agent must be stored separately. The shelf life is 12 months under normal room temperature conditions.
Safety
This product contains organic solvents and is a flammable anti-corrosive coating. All sources of ignition are strictly prohibited at the application site, and good ventilation must be maintained. Application personnel must wear respirator masks, safety glasses, and solvent-resistant gloves. Avoid inhalation of paint mist. In case of skin contact, wipe with a dedicated thinner first, then wash thoroughly with soap and water. In case of eye contact, rinse immediately with plenty of fresh water and seek medical attention.
免责声明
The protective performance of any coating depends largely on the application process. Application factors such as surface preparation and dry film thickness will directly impact the service life of the coating system. Users must ensure compliance with the specified application conditions when using this product.
All data in this technical datasheet are theoretical values or compiled based on laboratory experience. Due to continuous product improvement, some data may be subject to change without prior notice.
The Company is solely liable for the quality of the paint product itself if the Company’s technical personnel are not present at the application site.
