描述
物理参数
颜色： Red oxide
光泽： Flat / Matt
标准膜厚度：
湿薄膜厚度(WFT): $110,mu\text{m}$
干膜厚度(DFT): \(80\,\mu\text{m}\)
理论上传播率： 约。 $4.4\,\text{m}^2/\text{kg}$
闪点： $25^\circ\text{C}$
密度： 约。 $1.5\,\text{g/cm}^3$ (after mixing the two components)
应用程序的说明
混合比例： Base : Curing Agent = 10 : 1 (by weight)
锅生(23美元^\circ\文字{C}$): 2–4 hours (depending on ambient temperature)
稀释剂: Epoxy Thinner
Application Method: Airless Spray / Conventional (Air) Spray / Brush or Roller
| 参数 | 无气喷雾 | Conventional Spray | 刷/滚 |
| Nozzle/Orifice | (Graco) 163T-619／621 | 2~3 mm | – |
| 流体压力(MPa) | 15~35 | 0.3~0.4 | – |
| Thinned Volume | 0~5% | 5~15% | 5~15% |
Tool Cleaning: Specialized Thinner
Note: Application should preferably be done via airless spray or conventional spray. Brush application is recommended only for stripe coating and small areas, provided that the specified dry film thickness (DFT) is achieved. The airless spray parameters provided are for reference only and can be adjusted during practical application.
干燥的时间和间隔复涂
| 基Temp. (∘C) | 表面干(h) | 硬干(h) | Min. Overcoating (h) | Max. Overcoating (d) |
| 5 | 24 | 48 | 48 | 7 |
| 20 | 12 | 24 | 24 | 3 |
| 30 | 6 | 24 | 24 | 3 |
表面准备
New steel surfaces should be blast cleaned to Sa2.5 or St3 standard. For surfaces coated with shop primer, damaged and corroded areas must undergo secondary derusting to reach Sa2.5 or St3 standard. Any zinc salts formed on the shop primer surface should be removed by sweep blasting or high-pressure fresh water washing. Welds and burn-damaged areas must be treated to Sa2.5 or St3 standard.
应用程序的条件
The application temperature range is 5–$35^\circ\text{C}$, with relative humidity (RH) below 85%. The steel substrate surface temperature must be at least 3美元^\circ\文字{C}$ above the dew point. Temperature and humidity should be measured in the vicinity of the substrate. Do not apply paint during adverse weather conditions such as rain, snow, heavy winds, or sandstorms. After applying each coat, the inside of the tanks/compartments should be well-ventilated to expel odors and promote drying. If the ambient temperature is low, hot air should be forced into the tank to facilitate drying and curing.
Subseqent Coating System
随后的外套: High-solid epoxy polyamide topcoat
包装的规格
基地(A部分): 30 kg
固化剂(B部分): 3 kg
储存
This product must be stored in a cool, dry, and well-ventilated indoor warehouse, away from heat and ignition sources. Containers must be kept tightly closed. The shelf life is one year under normal room temperature conditions.
Safety
All sources of ignition are strictly prohibited at the paint mixing and application sites, and good ventilation must be maintained. Application personnel must wear protective equipment to prevent inhalation of paint mist and contact with eyes or skin. In case of skin contact, wash immediately with soap and water. In case of eye contact, rinse immediately with plenty of fresh water and seek medical attention.
免责声明
The protective performance of any coating depends largely on the application process. Application factors such as surface preparation and dry film thickness will directly impact the service life of the coating system. Users must ensure compliance with the specified application conditions when using this product.
All data in this technical datasheet are theoretical values or compiled based on laboratory experience. Due to continuous product improvement, some data may be subject to change without prior notice.
The Company is solely liable for the quality of the paint product itself if the Company’s technical personnel are not present at the application site.
