描述
物理参数
颜色： White, grey, blue, yellow, and customizable colors
光泽： Semi-gloss, Matt / Flat
标准膜厚度：
湿薄膜厚度(WFT): 90 μm
干膜厚度(DFT): 35 μm
理论上传播率： Approx. 8.0 ㎡/kg
闪点： Non-flammable
密度： 约。 1.25g/cm3
应用程序的说明
混合比例： Single-component; ready for use.
稀释剂: Deionized water
清洁剂： Tap water
应用的方法： 无空气喷洒，常规的空气喷洒，或者刷/罗涂层。
喷参数
| 参数 | 无气喷雾 | 常规的空中喷雾 | 刷/滚 |
| 喷嘴/尖端的尺寸 | (安全)163T-619/621 | 1.8 ~ 2.5 mm | — |
| 流体压力(MPa) | 15 ~ 35 | 0.3 ~ 0.5 | — |
| 疏比 | 0 ~ 5% | 0 ~ 15% | 0 ~ 5% |
Note: Airless and conventional air spray data are for reference only and can be adjusted based on onsite conditions during practical application.
干燥的时间和间隔复涂
| 基Temp. (°C) | Surface Dry (min) | 硬干(h) | 分。 复涂间间隔(h) | 最大。 复涂间间隔 |
| 5 | 90 | 20 | 10 | 没有限制 |
| 20 | 45 | 10 | 6 | 没有限制 |
| 30 | 30 | 6 | 4 | 没有限制 |
表面准备
The application baseline surface must be dry, clean, and completely free of oil stains, dust, and impurities. The preceding primer coat must be fully dry and free of surface dust or contamination.
When overcoating existing coatings, the old film must be abraded and roughened to eliminate chalked, peeling, or loose areas. Clean the surface thoroughly before application to guarantee optimal intercoat adhesion.
应用程序的条件
温度及湿度： The application temperature range is 5 ~ 40°C with a relative humidity (RH) below 80%. The substrate surface temperature must be at least 3°C above the dew point.
制约因素： Application is strictly prohibited during high humidity, condensing conditions, or heavy fog to prevent the film from experiencing whitening or loss of gloss. Outdoor application is not recommended during rain, snow, heavy winds, or dusty conditions.
Sub-Zero Warning: Construction and storage ambient temperatures must never fall below 0°C. Freezing temperatures will cause latex emulsion breakage (phase separation), rendering the coating ruined and unusable.
涂层系统的兼容性
Preceding Coats: Waterborne Acrylic Primer, Waterborne Epoxy Primer, Waterborne Zinc-Rich Primer, or Epoxy MIO (Micaceous Iron Oxide) Intermediate Paint.
System Constraint: Do not apply directly over aggressive solvent-borne coatings to prevent lifting or wrinkling (“paint biting”) of the undercoat.
包装的规格
20公斤/桶
储存
Store this product in a cool, dry, and well-ventilated indoor warehouse. Ensure protection against freezing and direct sunlight.
Avoid high-temperature exposure and sub-zero freezing. Maintain the storage temperature range between 5°C and 30°C. The shelf life is 12个月 under normal standard temperature conditions.
安全预防措施
This product is a waterborne coating and is safe and non-flammable. Maintain good ventilation throughout the application site.
Applicators must wear appropriate personal protective equipment (PPE), including dust/mist masks, protective gloves, and safety goggles. Avoid prolonged inhalation of paint mist.
If paint contacts the skin, wash thoroughly with soap and water. If it splashes accidentally into the eyes, rinse immediately with a large volume of water and seek immediate medical attention. Clean all tools with tap water immediately after use.
免责声明
保护性能的任何涂层在很大程度上取决于应用程序因素。 表面准备和薄膜厚度将会直接影响到服务的生活的涂层。 用户必须确保遵守规定的应用条件。
提供的数据，在这本手册是理论上的价值或来源于实验的积累。 一些数据可以改变由于持续的产品的改进，无须事先通知。
当我们的公司的技术人员都是不存在的应用程序的网站，该公司承担全部责任的质量的涂料产品本身。
